RFC 2335 A Distributed NHRP Service Using SCSP

[Docs] [txt|pdf] [draft-ietf-ion-...] [Tracker] [Diff1] [Diff2]

PROPOSED STANDARD

Network Working Group                                         J. Luciani
Request for Comments: 2335                                  Bay Networks
Category: Standards Track                                     April 1998


                 A Distributed NHRP Service Using SCSP

Status of this Memo

   This document specifies an Internet standards track protocol for the
   Internet community, and requests discussion and suggestions for
   improvements.  Please refer to the current edition of the "Internet
   Official Protocol Standards" (STD 1) for the standardization state
   and status of this protocol.  Distribution of this memo is unlimited.

Copyright Notice

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

Abstract

   This document describes a method for distributing an NHRP service
   within a LIS [1].  This method uses the Server Cache Synchronization
   Protocol (SCSP) [2] to synchronize the client information databases
   held by NHRP Servers (NHSs) within a LIS.

1. Introduction

   The keywords MUST, MUST NOT, REQUIRED, SHALL, SHALL NOT, SHOULD,
   SHOULD NOT, RECOMMENDED, MAY, and OPTIONAL, when they appear in this
   document, are to be interpreted as described in [4].

   NHRP Clients (NHCs) register their existence and reachability
   information with NHRP Servers (NHSs).  There may be multiple NHSs in
   a given Logical IP Subnet (LIS).  NHCs do not necessarily register
   with all NHSs in a LIS; however, all NHCs need to be able to query at
   least one NHS about any NHC within the LIS.  Thus, the contents of
   the NHS databases in a LIS need to be synchronized across the LIS.
   The Server Cache Synchronization Protocol (SCSP) solves the
   generalized server synchronization/cache-replication problem for
   distributed databases and thus SCSP may be applied to the NHS
   database synchronization problem within the LIS.









Luciani                     Standards Track                     [Page 1]


RFC 2335                    NHRP Using SCSP                   April 1998


   SCSP is defined in two parts: the protocol independent part and the
   client/server protocol specific part.  The protocol independent part
   is defined in [2] whereas this document will specify the
   client/server protocol specific part where NHRP is the client/server
   protocol.

   This document is separate from [2] because it was felt that it was
   desirable to allow the client/server protocol specific part
   specification for NHRP to progress independently from the protocol
   independent specification.

2. Overview

   All NHSs belonging to a Logical IP Subnet (LIS) [1] are said to
   belong to a Server Group (SG).  An SG is identified by, not
   surprisingly, its SGID which is contained in a field in all SCSP
   packets.  All SCSP packets contain a Protocol ID (PID) field as well.
   This PID field is set to 0x0002 to signify that SCSP synchronizing
   NHS databases as opposed to synchronizing some other protocol's
   databases (see Section B.2.0.1 of [2] for more details).  In general,
   PIDs for SCSP will be assigned by IANA as described in Section C of
   [2].  In the case of NHRP, the client/server protocol specific
   specification was initially written at the same time as SCSP, and
   thus a PID=0x0002 was assigned by the author.

   SCSP places no topological requirements upon an NHRP SG.  Obviously,
   however, the resultant graph of NHSs must span the set of NHSs to be
   synchronized.  For more information about the client/server protocol
   independent part of SCSP, the reader is encouraged to see [2].

   When a SG is using SCSP for synchronization, an NHC will register
   with only one NHS, but the NHC MAY use any NHS in the SG.  When an
   NHC wishes to leave a SG, the NHC MUST do one of the following: 1)
   the NHC MUST send an NHRP Purge Request for itself requesting a
   reply, and it MUST wait for an NHRP Purge Reply, 2) the NHC MUST keep
   the Request ID it used when registering itself in non-volatile RAM
   and use a Request ID larger than the one saved when re-registering,
   or 3) the NHC MUST not re-register for a time equal to the Holding
   Time specified in the previous registration.  It is necessary to do
   one of the previous in order to prevent the unlikely case of race
   conditions from occurring during updated.  In the case where method 2
   is used, the NHS with which the NHC registered uses its ID as the OID
   and the Request ID from the NHC as the CSA Sequence Number in the
   CSA(S) Record.







Luciani                     Standards Track                     [Page 2]


RFC 2335                    NHRP Using SCSP                   April 1998


3.  Format of the CSA Record NHRP Specific Part

   CSA Records in SCSP contain a "Client/Server Protocol Specific Part"
   which contains the non-protocol independent information for a given
   server's cache entry.

      0                   1                   2                   3
      0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Address Family Number     |     NHRP Protocol Type        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                             Snap                              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |     Snap      | NHRP Vers Num |            Flags              |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |                         Request ID                            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |    State      | Prefix Length |            unused             |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Maximum Transmission Unit    |        Holding Time           |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |  Cli Addr T/L | Cli SAddr T/L | Cli Proto Len |  Preference   |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          Client Subnetwork Address (variable length)          |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |         Client Subnetwork Subaddress (variable length)        |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
     |          Client Protocol Address (variable length)            |
     +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

   The following six fields contain values specified in the common
   header of the mandatory part of an NHRP Registration Request or NHRP
   Purge Request packet which caused the
   creation/deletion/modification/update/etc. of an NHS's cache entry.

   Address Family Number
     Defines the type of "link layer" addresses being carried.  This
     number is taken from the 'address family number' list specified in
     [3].  This field is the same field which would be supplied in an
     NHRP packet in the ar$afn field.

   NHRP Protocol Type
     This field is the same field which would be supplied in an NHRP
     packet in the ar$pro.type field.

   Snap
     This field is the same field which would be supplied in an NHRP
     packet in the ar$pro.snap field.



Luciani                     Standards Track                     [Page 3]


RFC 2335                    NHRP Using SCSP                   April 1998


   NHRP Vers Num
     This field indicates what version of generic address mapping and
     management protocol that is represented by this message.  This
     field contains 0x01 for the NHRP protocol version 1.  This field is
     the same field which would be supplied in an NHRP packet in the
     ar$op.version field.

   Flags
     Defined flags are as follows:

        0                   1
        0                   1
        0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
       |U|A|       unused              |
       +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+

       U
         This is the Uniqueness bit.

       A
         When set, this bit specifies that the cache entry was created
         as a result of ATMARP client interaction with the NHS.

   Request ID
     This field contains the Request ID value placed in the cache entry
     of the NHS as a result of an NHRP Registration Request.  This NHS
     is the NHS causing a synchronization event.

   State
     This field contains a value which represents the new state of the
     client.

       0 - Client is registered and available.
       1 - Client reregistered.
       2 - Client has been purged.
       3 - No such client data in server cache

     Note that a time-out of a cache entry does not cause a CSA Record
     to be sent because, if everything is working properly then all NHSs
     have the cache entry timing out at the same time.  Thus, the
     individual NHSs would take the appropriate actions necessary.

   The following ten fields contain values specified in or derived from
   the CIE of an NHRP Registration Request or NHRP Purge Request packet
   which caused the creation/deletion/modification/update/etc. of an
   NHS's cache entry.




Luciani                     Standards Track                     [Page 4]


RFC 2335                    NHRP Using SCSP                   April 1998


   Prefix Length
     This field contains the internetwork layer address prefix length
     value covered by the cache entry being synchronized.

   Maximum Transmission Unit
     This field contains a value supplied by or derived from information
     in the CIE of the NHRP Registration Request packet.

   Holding Time
     The Holding Time field specifies the number of seconds remaining
     for which the Next Hop NBMA information specified in the CIE of the
     NHRP Registration Request is considered to be valid by the NHS
     initiating the synchronization event.

   Cli Addr T/L
     Type & length of next hop NBMA address (see [1]).

   Cli SAddr T/L
     Type & length of next hop NBMA subaddress (see [1]).

   Cli Proto Len
     This field holds the length in octets of the Client Protocol
     Address.

   Preference
     This field specifies the preference value for use of the next hop
     NBMA information specified.

   Client NBMA Address
     This is the client's NBMA address.

   Client NBMA SubAddress
     This is the client's NBMA subaddress.

   Client Protocol Address
     This is the client's internetworking layer address.

4.  Values for SCSP Protocol Independent Part

   The following sections give values for fields of the SCSP Protocol
   Independent Part of the various SCSP messages.

4.1 Values for the SCSP "Mandatory Common Part"

   Protocol ID = 0x0002
   Sender ID Len = 0x04
   Recvr ID Len = 0x04




Luciani                     Standards Track                     [Page 5]


RFC 2335                    NHRP Using SCSP                   April 1998


   See Section B.2.0.1 of [2] for a detailed description of these
   fields.

4.2 Values for the SCSP "CSAS Record"

   Cache Key Len = 0x04
   Orig ID Len = 0x04

   See Section B.2.0.2 of [2] for a detailed description of these
   fields.

5. Security Considerations

   Relevant security considerations are documented in [1] and [2].

References

   [1] Luciani, J., Katz, D., Piscitello, D., Cole, B., and N.
   Doraswamy, "NMBA Next Hop Resolution Protocol (NHRP)", RFC 2332,
   April 1998.

   [2] Luciani, J., Armitage, G., Halpern, J., and N. Doraswamy, "Server
   Cache Synchronization Protocol (SCSP)", RFC 2334, April 1998.

   [3] Reynolds, J., and J. Postel, "Assigned Numbers", STD 2, RFC 1700,
   October 1994.

   [4] Bradner, S., "Key words for use in RFCs to Indicate Requirement
   Levels", BCP 14, RFC 2119, March 1997.

Acknowledgments

   I would like to thank (in no particular order) Maxine Burns of ISR
   and Joel Halpern of Newbridge.  I would also like to thank the
   members of the ION working group of the IETF, whose review and
   discussion of this document has been invaluable.

Author's Address

   James V. Luciani
   Bay Networks, Inc.
   3 Federal Street, BL3-03
   Billerica, MA  01821

   Phone: +1-978-916-4734
   EMail: luciani@baynetworks.com





Luciani                     Standards Track                     [Page 6]


RFC 2335                    NHRP Using SCSP                   April 1998


Full Copyright Statement

   Copyright (C) The Internet Society (1998).  All Rights Reserved.

   This document and translations of it may be copied and furnished to
   others, and derivative works that comment on or otherwise explain it
   or assist in its implementation may be prepared, copied, published
   and distributed, in whole or in part, without restriction of any
   kind, provided that the above copyright notice and this paragraph are
   included on all such copies and derivative works.  However, this
   document itself may not be modified in any way, such as by removing
   the copyright notice or references to the Internet Society or other
   Internet organizations, except as needed for the purpose of
   developing Internet standards in which case the procedures for
   copyrights defined in the Internet Standards process must be
   followed, or as required to translate it into languages other than
   English.

   The limited permissions granted above are perpetual and will not be
   revoked by the Internet Society or its successors or assigns.

   This document and the information contained herein is provided on an
   "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
   TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
   BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
   HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
   MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
























Luciani                     Standards Track                     [Page 7]


Html markup produced by rfcmarkup 1.129b, available from https://tools.ietf.org/tools/rfcmarkup/