[Docs] [txt|pdf] [draft-ietf-ipcd...] [Tracker] [Diff1] [Diff2] [Errata]
INFORMATIONAL
Errata Exist
Network Working Group R. Woundy
Request for Comments: 3083 Cisco Systems
Category: Informational March 2001
Baseline Privacy Interface Management Information Base
for DOCSIS Compliant Cable Modems and Cable Modem Termination Systems
Status of this Memo
This memo provides information for the Internet community. It does
not specify an Internet standard of any kind. Distribution of this
memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2001). All Rights Reserved.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in the Internet community.
In particular, it defines a basic set of managed objects for SNMP-
based (Simple Network Management Protocol) management of the Baseline
Privacy Interface (BPI), which provides data privacy for DOCSIS 1.0
(Data-Over-Cable Service Interface Specifications) compliant Cable
Modems and Cable Modem Termination Systems. This MIB is defined as
an extension to the DOCSIS Radio Frequency Interface MIB, RFC 2670.
This memo specifies a MIB module in a manner that is compliant to the
SMIv2 (Structure of Management Information Version 2). The set of
objects is consistent with the SNMP framework and existing SNMP
standards.
CableLabs requires the implementation of this MIB in DOCSIS 1.0 cable
modems that implement the Baseline Privacy Interface, as a
prerequisite for DOCSIS 1.0 certification.
Woundy Informational [Page 1]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
Table of Contents
1 The SNMP Management Framework ................................... 2
2 Glossary ........................................................ 3
2.1 Authorization key ............................................. 3
2.2 BPI ........................................................... 4
2.3 BPI+ .......................................................... 4
2.4 CATV .......................................................... 4
2.5 CM ............................................................ 4
2.6 CMTS .......................................................... 4
2.7 DOCSIS ........................................................ 4
2.8 Downstream .................................................... 4
2.9 Head-end ...................................................... 4
2.10 MAC Packet ................................................... 4
2.11 MCNS ......................................................... 5
2.12 RF ........................................................... 5
2.13 SID .......................................................... 5
2.14 TEK .......................................................... 5
2.15 Upstream ..................................................... 5
3 Overview ........................................................ 5
3.1 Structure of the MIB .......................................... 5
3.2 Management requirements ....................................... 6
3.3 Textual convention ............................................ 7
4 Definitions ..................................................... 8
5 Acknowledgments ................................................ 40
6 References ..................................................... 40
7 Security Considerations ........................................ 42
8 Intellectual Property .......................................... 43
9 Author's Address ............................................... 44
10 Full Copyright Statement ...................................... 45
1. The SNMP Management Framework
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and described in STD
16, RFC 1155 [2], STD 16, RFC 1212 [3] and RFC 1215 [4]. The
second version, called SMIv2, is described in STD 58, RFC 2578
[5], RFC 2579 [6] and RFC 2580 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and
described in STD 15, RFC 1157 [8]. A second version of the SNMP
Woundy Informational [Page 2]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described in RFC 1901 [9] and RFC
1906 [10]. The third version of the message protocol is called
SNMPv3 and described in RFC 1906 [10], RFC 2572 [11] and RFC 2574
[12].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[13].
o A set of fundamental applications described in RFC 2573 [14] and
the view-based access control mechanism described in RFC 2575
[15].
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [24].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
2. Glossary
The terms in this document are derived either from normal cable
system usage, or from the documents associated with the Data Over
Cable Service Interface Specification process.
2.1. Authorization key
A key used to derive a key encryption key (used to encrypt TEKs), and
to derive message authentication keys. When the CMTS communicates
the authorization key to the CM, it encrypts the authorization key
using the RSA public key of the CM [22].
Woundy Informational [Page 3]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
2.2. BPI - Baseline Privacy Interface
A term referring to the DOCSIS specification [18] for enabling simple
data privacy in the DOCSIS 1.0 system. Management of the BPI is the
focus of this document.
2.3. BPI+ - Baseline Privacy Plus Interface
A term referring to the DOCSIS specification [21] for enabling CM
authentication and data privacy in the DOCSIS 1.1 system. Management
of the BPI+ is not addressed in this document.
2.4. CATV
Originally "Community Antenna Television", now used to refer to any
cable or hybrid fiber and cable system used to deliver video signals
to a community.
2.5. CM - Cable Modem
A CM acts as a "slave" station in a DOCSIS compliant cable data
system.
2.6. CMTS - Cable Modem Termination System
A generic term covering a cable bridge or cable router in a head-end.
A CMTS acts as the master station in a DOCSIS compliant cable data
system. It is the only station that transmits downstream, and it
controls the scheduling of upstream transmissions by its associated
CMs.
2.7. DOCSIS
"Data-Over-Cable Service Interface Specifications". A term referring
to the ITU-T J.112 Annex B standard for cable modem systems [19].
2.8. Downstream
The direction from the head-end towards the subscriber.
2.9. Head-end
The origination point in most cable systems of the subscriber video
signals. Generally also the location of the CMTS equipment.
2.10. MAC Packet
A DOCSIS PDU.
Woundy Informational [Page 4]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
2.11. MCNS
"Multimedia Cable Network System". Generally replaced in usage by
DOCSIS.
2.12. RF
Radio Frequency.
2.13 SID
Service ID. The SID identifies a particular upstream bandwidth
allocation and class-of-service management for DOCSIS, and identifies
a particular bidirectional security association for BPI.
2.14. TEK - Traffic Encryption Key
Traffic Encryption Key, which is used for DES encryption of upstream
and downstream traffic. When the CMTS communicates the TEK to the
CM, it encrypts the TEK using the key encryption key derived from the
authorization key.
2.15. Upstream
The direction from the subscriber towards the head-end.
3. Overview
This MIB provides a set of objects required for the management of the
Baseline Privacy Interface for DOCSIS compliant Cable Modems (CMs)
and Cable Modem Termination Systems (CMTSs). This MIB specification
is derived from the DOCSIS Baseline Privacy Interface specification
[18], which is an extension to the DOCSIS Radio Frequency Interface
specification [19].
Please note that this MIB specification is not sufficient for the
management of the DOCSIS Baseline Privacy Plus Interface
specification [21]. The working group expects to issue a MIB for the
management of BPI+ at a later time.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in [23].
3.1. Structure of the MIB
This MIB consists of one group of CM-only objects (docsBpiCmGroup),
and one group of CMTS-only objects (docsBpiCmtsGroup).
Woundy Informational [Page 5]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
The CM-only objects are organized into two tables:
o The docsBpiCmBaseTable contains objects for managing basic
Baseline Privacy parameters and counters, and for managing the
Authorization finite state machine.
o The docsBpiCmTEKTable contains objects for managing the Traffic
Encryption Key (TEK) finite state machine per SID.
The CMTS-only objects are organized into four sub-groups:
o The docsBpiCmtsBaseTable contains objects for managing basic
Baseline Privacy parameters and counters.
o The docsBpiCmtsAuthTable contains objects for managing the
Authorization association information per cable modem.
o The docsBpiCmtsTEKTable contains objects for managing the TEK
association information per SID.
o The docsBpiMulticastControl consists of two tables. The
docsBpiIpMulticastMapTable controls the mapping of downstream IP
multicast data traffic to downstream multicast SID values. The
docsBpiMulticastAuthTable controls which CMs are authorized to
receive downstream traffic transmitted over particular multicast
SIDs; a CM will receive TEKs corresponding to the multicast SIDs
for which it is authorized. The combination of these two tables
will limit the distribution of downstream IP multicast data
traffic to authorized CMs.
3.2. Management requirements
The Baseline Privacy Interface specification is documented in [18],
and is an extension to the Radio Frequency Interface specification
documented in [19]. In addition to the explicit requirements in this
specification, the CM and CMTS enabled for Baseline Privacy MUST
support all applicable DOCSIS and IETF requirements and MIB objects.
Specifications that identify relevant requirements and MIB objects
include the IETF Radio Frequency MIB [16], the IETF Cable Device MIB
[17], and the DOCSIS OSSI Specification [20].
The explicit management requirements of the Baseline Privacy
Interface, which motivate the development of the MIB in this
document, are detailed below:
o The CM and CMTS MUST support viewing relevant RSA public keys, for
future subscriber authentication applications.
Woundy Informational [Page 6]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
o The Baseline Privacy management interface needs to support
operator configuration of Authorization and TEK Finite State
Machine (FSM) parameters, for performance tuning and security
incident handling. The CMTS MUST support viewing (and configuring
if possible) all FSM-related parameters, including baseline
privacy status (enabled or disabled), key lifetimes, key grace
times, and state timeout values. The CM MUST support viewing
these parameters where possible.
o The management interface needs to support operator analysis and
override of FSM behavior, for fault management, subscriber service
de-provisioning, and security incident handling. The CM MUST
support viewing the current FSM states. The CM and CMTS MUST
support viewing message error codes and message error strings, and
counters for invalid KEK and TEK events, for key expirations and
renewals, and for duplicate messages. The CM and CMTS MUST
support viewing current authorization key sequence numbers and key
expiration times for failure diagnosis.
o The management interface needs to support dynamic control of the
distribution of IP multicast data traffic. This control includes
forwarding IP multicast traffic to the correct multicast group
(SID), and managing the membership lists of each multicast group
(SID). The CMTS MUST support configuring and viewing all IP
multicast forwarding state, and all multicast group memberships,
within the MAC domains of the CMTS.
3.3. Textual convention
CableLabs has required the implementation of prior versions of this
MIB in DOCSIS 1.0 cable modems that implement the Baseline Privacy
Interface, as a prerequisite for DOCSIS 1.0 certification.
The Baseline Privacy Interface MIB contains eight MIB objects defined
with the (now obsolete) DisplayString textual convention, and one MIB
object defined with the (now undesirable) IpAddress textual
convention.
In the judgment of the working group, it is preferable to keep these
less-than-desirable textual conventions, in order to maintain
backward compatibility and interoperability with DOCSIS 1.0 cable
modems that implemented previous versions of this MIB.
Woundy Informational [Page 7]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
4. Definitions
DOCS-BPI-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE,
Integer32, Counter32, IpAddress
FROM SNMPv2-SMI
DisplayString, MacAddress, RowStatus, TruthValue, DateAndTime
FROM SNMPv2-TC
OBJECT-GROUP, MODULE-COMPLIANCE
FROM SNMPv2-CONF
ifIndex
FROM IF-MIB
docsIfMib, docsIfCmServiceId, docsIfCmtsServiceId
FROM DOCS-IF-MIB
;
docsBpiMIB MODULE-IDENTITY
LAST-UPDATED "200103130000Z"
ORGANIZATION "IETF IPCDN Working Group"
CONTACT-INFO "Rich Woundy
Postal: Cisco Systems
250 Apollo Drive
Chelmsford, MA 01824 U.S.A.
Tel: +1 978 244 8000
E-mail: rwoundy@cisco.com
IETF IPCDN Working Group
General Discussion: ipcdn@ietf.org
Subscribe: http://www.ietf.org/mailman/listinfo/ipcdn
Archive: ftp://ftp.ietf.org/ietf-mail-archive/ipcdn
Co-chairs: Richard Woundy, rwoundy@cisco.com
Andrew Valentine, a.valentine@eu.hns.com"
DESCRIPTION
"This is the MIB Module for the DOCSIS Baseline Privacy Interface
(BPI) at cable modems (CMs) and cable modem termination systems
(CMTSs). CableLabs requires the implementation of this MIB in
DOCSIS 1.0 cable modems that implement the Baseline Privacy
Interface, as a prerequisite for DOCSIS 1.0 certification."
REVISION "200103130000Z"
DESCRIPTION
"Version published as RFC 3083."
REVISION "200011031930Z"
DESCRIPTION
"Modified by Richard Woundy to fix problems identified by the MIB
Woundy Informational [Page 8]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
doctor. I marked docsBpiCmtsDefaultAuthGraceTime and
docsBpiCmtsDefaultTEKGraceTime as obsolete objects, to prevent OID
reassignment. Several object descriptions were also corrected."
REVISION "200002161930Z"
DESCRIPTION
"Initial version.
CableLabs requires the implementation of this MIB in certified DOCSIS
1.0 cable modems implementing the Baseline Privacy Interface, per
DOCSIS 1.0 engineering change notice oss-n-99027."
::= { docsIfMib 5 }
docsBpiMIBObjects OBJECT IDENTIFIER ::= { docsBpiMIB 1 }
-- Cable Modem Group
docsBpiCmObjects OBJECT IDENTIFIER ::= { docsBpiMIBObjects 1 }
--
-- The BPI base and authorization table for CMs, indexed by ifIndex
--
docsBpiCmBaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiCmBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the basic and authorization-related Baseline
Privacy attributes of each CM MAC interface."
::= { docsBpiCmObjects 1 }
docsBpiCmBaseEntry OBJECT-TYPE
SYNTAX DocsBpiCmBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of one CM MAC
interface. An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsBpiCmBaseTable 1 }
DocsBpiCmBaseEntry ::= SEQUENCE {
docsBpiCmPrivacyEnable TruthValue,
docsBpiCmPublicKey OCTET STRING,
docsBpiCmAuthState INTEGER,
docsBpiCmAuthKeySequenceNumber Integer32,
docsBpiCmAuthExpires DateAndTime,
Woundy Informational [Page 9]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmAuthReset TruthValue,
docsBpiCmAuthGraceTime Integer32,
docsBpiCmTEKGraceTime Integer32,
docsBpiCmAuthWaitTimeout Integer32,
docsBpiCmReauthWaitTimeout Integer32,
docsBpiCmOpWaitTimeout Integer32,
docsBpiCmRekeyWaitTimeout Integer32,
docsBpiCmAuthRejectWaitTimeout Integer32,
docsBpiCmAuthRequests Counter32,
docsBpiCmAuthReplies Counter32,
docsBpiCmAuthRejects Counter32,
docsBpiCmAuthInvalids Counter32,
docsBpiCmAuthRejectErrorCode INTEGER,
docsBpiCmAuthRejectErrorString DisplayString,
docsBpiCmAuthInvalidErrorCode INTEGER,
docsBpiCmAuthInvalidErrorString DisplayString
}
docsBpiCmPrivacyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies whether this CM is provisioned to run
Baseline Privacy. This is analogous to the presence (or absence)
of the Baseline Privacy Configuration Setting option. The status
of each individual SID with respect to Baseline Privacy is
captured in the docsBpiCmTEKPrivacyEnable object."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1."
::= { docsBpiCmBaseEntry 1 }
docsBpiCmPublicKey OBJECT-TYPE
SYNTAX OCTET STRING (SIZE (74 | 106 | 140 | 270))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is a DER-encoded RSAPublicKey ASN.1 type
string, as defined in the RSA Encryption Standard (PKCS #1) [22],
corresponding to the public key of the CM. The 74, 106, 140, and
270 byte key encoding lengths correspond to 512 bit, 768 bit, 1024
bit, and 2048 public moduli respectively."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.2.4."
::= { docsBpiCmBaseEntry 2 }
docsBpiCmAuthState OBJECT-TYPE
SYNTAX INTEGER {
Woundy Informational [Page 10]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
authWait(2),
authorized(3),
reauthWait(4),
authRejectWait(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the state of the CM authorization
FSM. The start state indicates that FSM is in its initial state."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.1.2.1."
::= { docsBpiCmBaseEntry 3 }
docsBpiCmAuthKeySequenceNumber OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the authorization key sequence number
for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2
and 4.2.2.10."
::= { docsBpiCmBaseEntry 4 }
docsBpiCmAuthExpires OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time when the current
authorization for this FSM expires. If the CM does not have an active
authorization, then the value is of the expiration date and time of
the last active authorization."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2
and 4.2.2.9."
::= { docsBpiCmBaseEntry 5 }
docsBpiCmAuthReset OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to TRUE generates a Reauthorize event in the
authorization FSM. Reading this object always returns FALSE."
REFERENCE
Woundy Informational [Page 11]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
"DOCSIS Baseline Privacy Interface Specification, Section 4.1.2.3.4."
::= { docsBpiCmBaseEntry 6 }
docsBpiCmAuthGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for an authorization key.
A CM is expected to start trying to get a new authorization key
beginning AuthGraceTime seconds before the authorization key actually
expires."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.3."
::= { docsBpiCmBaseEntry 7 }
docsBpiCmTEKGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for a TEK. A CM is
expected to start trying to get a new TEK beginning TEKGraceTime
seconds before the TEK actually expires."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.6."
::= { docsBpiCmBaseEntry 8 }
docsBpiCmAuthWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..30)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Authorize Wait Timeout."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.1."
::= { docsBpiCmBaseEntry 9 }
docsBpiCmReauthWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..30)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Reauthorize Wait Timeout in seconds."
Woundy Informational [Page 12]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.2."
::= { docsBpiCmBaseEntry 10 }
docsBpiCmOpWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..10)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Operational Wait Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.4."
::= { docsBpiCmBaseEntry 11 }
docsBpiCmRekeyWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..10)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Rekey Wait Timeout in seconds."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.5."
::= { docsBpiCmBaseEntry 12 }
docsBpiCmAuthRejectWaitTimeout OBJECT-TYPE
SYNTAX Integer32 (1..600)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Authorization Reject Wait Timeout in
seconds."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.7."
::= { docsBpiCmBaseEntry 13 }
docsBpiCmAuthRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has
transmitted an Authorization Request message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1."
::= { docsBpiCmBaseEntry 14 }
Woundy Informational [Page 13]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmAuthReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has
received an Authorization Reply message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2."
::= { docsBpiCmBaseEntry 15 }
docsBpiCmAuthRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has
received an Authorization Reject message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3."
::= { docsBpiCmBaseEntry 16 }
docsBpiCmAuthInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has
received an Authorization Invalid message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7."
::= { docsBpiCmBaseEntry 17 }
docsBpiCmAuthRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unauthorizedSid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent Authorization Reject message received by
the CM. This has value unknown(2) if the last Error-Code value was
0, and none(1) if no Authorization Reject message has been received
since reboot."
Woundy Informational [Page 14]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3
and 4.2.2.16."
::= { docsBpiCmBaseEntry 18 }
docsBpiCmAuthRejectErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent
Authorization Reject message received by the CM. This is a zero
length string if no Authorization Reject message has been received
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3
and 4.2.2.6."
::= { docsBpiCmBaseEntry 19 }
docsBpiCmAuthInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unsolicited(5),
invalidKeySequence(6),
keyRequestAuthenticationFailure(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent Authorization Invalid message received by
the CM. This has value unknown(2) if the last Error-Code value was
0, and none(1) if no Authorization Invalid message has been received
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7
and 4.2.2.16."
::= { docsBpiCmBaseEntry 20 }
docsBpiCmAuthInvalidErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent
Authorization Invalid message received by the CM. This is a zero
Woundy Informational [Page 15]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
length string if no Authorization Invalid message has been received
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7
and 4.2.2.6."
::= { docsBpiCmBaseEntry 21 }
--
-- The CM TEK Table, indexed by ifIndex and SID
--
docsBpiCmTEKTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiCmTEKEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the attributes of each CM Traffic Encryption Key
(TEK) association. The CM maintains (no more than) one TEK association
per SID per CM MAC interface."
::= { docsBpiCmObjects 2 }
docsBpiCmTEKEntry OBJECT-TYPE
SYNTAX DocsBpiCmTEKEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing the TEK association attributes
of one SID. The CM MUST create one entry per unicast SID, regardless
of whether the SID was obtained from a Registration Response message,
or from an Authorization Reply message."
INDEX { ifIndex, docsIfCmServiceId }
::= { docsBpiCmTEKTable 1 }
DocsBpiCmTEKEntry ::= SEQUENCE {
docsBpiCmTEKPrivacyEnable TruthValue,
docsBpiCmTEKState INTEGER,
docsBpiCmTEKExpiresOld DateAndTime,
docsBpiCmTEKExpiresNew DateAndTime,
docsBpiCmTEKKeyRequests Counter32,
docsBpiCmTEKKeyReplies Counter32,
docsBpiCmTEKKeyRejects Counter32,
docsBpiCmTEKInvalids Counter32,
docsBpiCmTEKAuthPends Counter32,
docsBpiCmTEKKeyRejectErrorCode INTEGER,
docsBpiCmTEKKeyRejectErrorString DisplayString,
docsBpiCmTEKInvalidErrorCode INTEGER,
docsBpiCmTEKInvalidErrorString DisplayString
}
Woundy Informational [Page 16]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmTEKPrivacyEnable OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object identifies whether this SID is provisioned to run
Baseline Privacy. This is analogous to enabling Baseline Privacy on
a provisioned SID using the Class-of-Service Privacy Enable option.
Baseline Privacy is not effectively enabled for any SID unless
Baseline Privacy is enabled for the CM, which is managed via the
docsBpiCmPrivacyEnable object."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.2."
::= { docsBpiCmTEKEntry 1 }
docsBpiCmTEKState OBJECT-TYPE
SYNTAX INTEGER {
start(1),
opWait(2),
opReauthWait(3),
operational(4),
rekeyWait(5),
rekeyReauthWait(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the state of the indicated TEK FSM.
The start(1) state indicates that FSM is in its initial state."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.1."
::= { docsBpiCmTEKEntry 2 }
docsBpiCmTEKExpiresOld OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for expiration
of the immediate predecessor of the most recent TEK for this FSM.
If this FSM has only one TEK, then the value is the time of activation
of this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and
4.2.2.9."
::= { docsBpiCmTEKEntry 3 }
docsBpiCmTEKExpiresNew OBJECT-TYPE
Woundy Informational [Page 17]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for expiration
of the most recent TEK for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5 and
4.2.2.9."
::= { docsBpiCmTEKEntry 4 }
docsBpiCmTEKKeyRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has transmitted
a Key Request message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.4."
::= { docsBpiCmTEKEntry 5 }
docsBpiCmTEKKeyReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has received
a Key Reply message, including a message whose authentication failed."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5."
::= { docsBpiCmTEKEntry 6 }
docsBpiCmTEKKeyRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CM has received
a Key Reject message, including a message whose authentication failed."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.6."
::= { docsBpiCmTEKEntry 7 }
docsBpiCmTEKInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Woundy Informational [Page 18]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
DESCRIPTION
"The value of this object is the count of times the CM has received
a TEK Invalid message, including a message whose authentication failed."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.8."
::= { docsBpiCmTEKEntry 8 }
docsBpiCmTEKAuthPends OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times an Authorization
Pending (Auth Pend) event occurred in this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.3.3."
::= { docsBpiCmTEKEntry 9 }
docsBpiCmTEKKeyRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedSid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent Key Reject message received by the CM. This
has value unknown(2) if the last Error-Code value was 0, and none(1)
if no Key Reject message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.6
and 4.2.2.16."
::= { docsBpiCmTEKEntry 10 }
docsBpiCmTEKKeyRejectErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent Key
Reject message received by the CM. This is a zero length string if no
Key Reject message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.6
and 4.2.2.6."
::= { docsBpiCmTEKEntry 11 }
Woundy Informational [Page 19]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmTEKInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
invalidKeySequence(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent TEK Invalid message received by the CM.
This has value unknown(2) if the last Error-Code value was 0, and
none(1) if no TEK Invalid message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.8
and 4.2.2.16."
::= { docsBpiCmTEKEntry 12 }
docsBpiCmTEKInvalidErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent TEK
Invalid message received by the CM. This is a zero length string if
no TEK Invalid message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.8
and 4.2.2.6."
::= { docsBpiCmTEKEntry 13 }
-- Cable Modem Termination System Group
docsBpiCmtsObjects OBJECT IDENTIFIER ::= { docsBpiMIBObjects 2 }
--
-- The BPI base table for CMTSs, indexed by ifIndex
--
docsBpiCmtsBaseTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiCmtsBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the basic Baseline Privacy attributes of each
CMTS MAC interface."
::= { docsBpiCmtsObjects 1 }
Woundy Informational [Page 20]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmtsBaseEntry OBJECT-TYPE
SYNTAX DocsBpiCmtsBaseEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of one CMTS MAC
interface. An entry in this table exists for each ifEntry with an
ifType of docsCableMaclayer(127)."
INDEX { ifIndex }
::= { docsBpiCmtsBaseTable 1 }
DocsBpiCmtsBaseEntry ::= SEQUENCE {
docsBpiCmtsDefaultAuthLifetime Integer32,
docsBpiCmtsDefaultTEKLifetime Integer32,
docsBpiCmtsDefaultAuthGraceTime Integer32,
docsBpiCmtsDefaultTEKGraceTime Integer32,
docsBpiCmtsAuthRequests Counter32,
docsBpiCmtsAuthReplies Counter32,
docsBpiCmtsAuthRejects Counter32,
docsBpiCmtsAuthInvalids Counter32
}
docsBpiCmtsDefaultAuthLifetime OBJECT-TYPE
SYNTAX Integer32 (1..6048000)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the default lifetime, in seconds, the
CMTS assigns to a new authorization key."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.2."
::= { docsBpiCmtsBaseEntry 1 }
docsBpiCmtsDefaultTEKLifetime OBJECT-TYPE
SYNTAX Integer32 (1..604800)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the default lifetime, in seconds, the
CMTS assigns to a new Traffic Encryption Key (TEK)."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.2."
::= { docsBpiCmtsBaseEntry 2 }
-- Note: the following two objects have been obsoleted from this MIB.
Woundy Informational [Page 21]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmtsDefaultAuthGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-write
STATUS obsolete
DESCRIPTION
"This object was obsoleted because the provisioning system, not the CMTS,
manages the authorization key grace time for DOCSIS CMs."
::= { docsBpiCmtsBaseEntry 3 }
docsBpiCmtsDefaultTEKGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-write
STATUS obsolete
DESCRIPTION
"This object was obsoleted because the provisioning system, not the CMTS,
manages the Traffic Encryption Key (TEK) grace time for DOCSIS CMs."
::= { docsBpiCmtsBaseEntry 4 }
docsBpiCmtsAuthRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
received an Authorization Request message from any CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1."
::= { docsBpiCmtsBaseEntry 5 }
docsBpiCmtsAuthReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted an Authorization Reply message to any CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2."
::= { docsBpiCmtsBaseEntry 6 }
docsBpiCmtsAuthRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
Woundy Informational [Page 22]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
transmitted an Authorization Reject message to any CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3."
::= { docsBpiCmtsBaseEntry 7 }
docsBpiCmtsAuthInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted an Authorization Invalid message to any CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7."
::= { docsBpiCmtsBaseEntry 8 }
--
-- The CMTS Authorization Table, indexed by ifIndex and CM MAC address
--
docsBpiCmtsAuthTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiCmtsAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the attributes of each CM authorization
association. The CMTS maintains one authorization association with
each Baseline Privacy-enabled CM on each CMTS MAC interface."
::= { docsBpiCmtsObjects 2 }
docsBpiCmtsAuthEntry OBJECT-TYPE
SYNTAX DocsBpiCmtsAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of one
authorization association. The CMTS MUST create one entry per CM per
MAC interface, based on the receipt of an Authorization Request
message, and MUST not delete the entry before the CM authorization
permanently expires."
INDEX { ifIndex, docsBpiCmtsAuthCmMacAddress }
::= { docsBpiCmtsAuthTable 1 }
DocsBpiCmtsAuthEntry ::= SEQUENCE {
docsBpiCmtsAuthCmMacAddress MacAddress,
docsBpiCmtsAuthCmPublicKey OCTET STRING,
docsBpiCmtsAuthCmKeySequenceNumber Integer32,
docsBpiCmtsAuthCmExpires DateAndTime,
Woundy Informational [Page 23]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmtsAuthCmLifetime Integer32,
docsBpiCmtsAuthCmGraceTime Integer32,
docsBpiCmtsAuthCmReset INTEGER,
docsBpiCmtsAuthCmRequests Counter32,
docsBpiCmtsAuthCmReplies Counter32,
docsBpiCmtsAuthCmRejects Counter32,
docsBpiCmtsAuthCmInvalids Counter32,
docsBpiCmtsAuthRejectErrorCode INTEGER,
docsBpiCmtsAuthRejectErrorString DisplayString,
docsBpiCmtsAuthInvalidErrorCode INTEGER,
docsBpiCmtsAuthInvalidErrorString DisplayString
}
docsBpiCmtsAuthCmMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The value of this object is the physical address of the CM to
which the authorization association applies."
::= { docsBpiCmtsAuthEntry 1 }
docsBpiCmtsAuthCmPublicKey OBJECT-TYPE
SYNTAX OCTET STRING
(SIZE (0 | 74 | 106 | 140 | 270))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is a DER-encoded RSAPublicKey ASN.1 type
string, as defined in the RSA Encryption Standard (PKCS #1) [22],
corresponding to the public key of the CM. The 74, 106, 140, and
270 byte key encoding lengths correspond to 512 bit, 768 bit, 1024
bit, and 2048 public moduli respectively. This is a zero-length
string if the CMTS does not retain the public key."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.2.4."
::= { docsBpiCmtsAuthEntry 2 }
docsBpiCmtsAuthCmKeySequenceNumber OBJECT-TYPE
SYNTAX Integer32 (0..15)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the authorization key sequence number
for this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2
and 4.2.2.10."
Woundy Informational [Page 24]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
::= { docsBpiCmtsAuthEntry 3 }
docsBpiCmtsAuthCmExpires OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time when the current
authorization for this CM expires. If this CM does not have an
active authorization, then the value is of the expiration date and
time of the last active authorization."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.2
and 4.2.2.9."
::= { docsBpiCmtsAuthEntry 4 }
docsBpiCmtsAuthCmLifetime OBJECT-TYPE
SYNTAX Integer32 (1..6048000)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the lifetime, in seconds, the CMTS
assigns to an authorization key for this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2
and Appendix A.2."
::= { docsBpiCmtsAuthEntry 5 }
docsBpiCmtsAuthCmGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for the authorization key
in seconds. The CM is expected to start trying to get a new
authorization key beginning AuthGraceTime seconds before the
authorization key actually expires."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.3."
::= { docsBpiCmtsAuthEntry 6 }
docsBpiCmtsAuthCmReset OBJECT-TYPE
SYNTAX INTEGER {
noResetRequested(1),
invalidateAuth(2),
sendAuthInvalid(3),
Woundy Informational [Page 25]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
invalidateTeks(4)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to invalidateAuth(2) causes the CMTS to
invalidate the current CM authorization key, but not to transmit an
Authorization Invalid message nor to invalidate unicast TEKs. Setting
this object to sendAuthInvalid(3) causes the CMTS to invalidate the
current CM authorization key, and to transmit an Authorization Invalid
message to the CM, but not to invalidate unicast TEKs. Setting this
object to invalidateTeks(4) causes the CMTS to invalidate the current
CM authorization key, to transmit an Authorization Invalid message to
the CM, and to invalidate all unicast TEKs associated with this CM
authorization. Reading this object returns the most-recently-set value
of this object, or returns noResetRequested(1) if the object has not
been set since the last CMTS reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.1.2.3.4,
4.1.2.3.5, and 4.1.3.3.5."
::= { docsBpiCmtsAuthEntry 7 }
docsBpiCmtsAuthCmRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
received an Authorization Request message from this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.1."
::= { docsBpiCmtsAuthEntry 8 }
docsBpiCmtsAuthCmReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted an Authorization Reply message to this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.2."
::= { docsBpiCmtsAuthEntry 9 }
docsBpiCmtsAuthCmRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
Woundy Informational [Page 26]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted an Authorization Reject message to this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.3."
::= { docsBpiCmtsAuthEntry 10 }
docsBpiCmtsAuthCmInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted an Authorization Invalid message to this CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.7."
::= { docsBpiCmtsAuthEntry 11 }
docsBpiCmtsAuthRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unauthorizedSid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent Authorization Reject message transmitted to
the CM. This has value unknown(2) if the last Error-Code value was
0, and none(1) if no Authorization Reject message has been transmitted
to the CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3
and 4.2.2.16."
::= { docsBpiCmtsAuthEntry 12 }
docsBpiCmtsAuthRejectErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent
Authorization Reject message transmitted to the CM. This is a
zero length string if no Authorization Reject message has been
transmitted to the CM."
REFERENCE
Woundy Informational [Page 27]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.3
and 4.2.2.6."
::= { docsBpiCmtsAuthEntry 13 }
docsBpiCmtsAuthInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedCm(3),
unsolicited(5),
invalidKeySequence(6),
keyRequestAuthenticationFailure(7)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in most recent Authorization Invalid message transmitted
to the CM. This has value unknown(2) if the last Error-Code value was
0, and none(1) if no Authorization Invalid message has been
transmitted to the CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7
and 4.2.2.16."
::= { docsBpiCmtsAuthEntry 14 }
docsBpiCmtsAuthInvalidErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in most recent
Authorization Invalid message transmitted to the CM. This is a
zero length string if no Authorization Invalid message has been
transmitted to the CM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.7
and 4.2.2.6."
::= { docsBpiCmtsAuthEntry 15 }
--
-- The CMTS TEK Table, indexed by ifIndex and SID
--
docsBpiCmtsTEKTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiCmtsTEKEntry
MAX-ACCESS not-accessible
STATUS current
Woundy Informational [Page 28]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
DESCRIPTION
"This table describes the attributes of each CM Traffic Encryption
Key (TEK) association. The CMTS maintains one TEK association per BPI
SID on each CMTS MAC interface."
::= { docsBpiCmtsObjects 3 }
docsBpiCmtsTEKEntry OBJECT-TYPE
SYNTAX DocsBpiCmtsTEKEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing attributes of one TEK
association on a particular CMTS MAC interface. The CMTS MUST create
one entry per SID per MAC interface, based on the receipt of an
Key Request message, and MUST not delete the entry before the CM
authorization for the SID permanently expires."
INDEX { ifIndex, docsIfCmtsServiceId }
::= { docsBpiCmtsTEKTable 1 }
DocsBpiCmtsTEKEntry ::= SEQUENCE {
docsBpiCmtsTEKLifetime Integer32,
docsBpiCmtsTEKGraceTime Integer32,
docsBpiCmtsTEKExpiresOld DateAndTime,
docsBpiCmtsTEKExpiresNew DateAndTime,
docsBpiCmtsTEKReset TruthValue,
docsBpiCmtsKeyRequests Counter32,
docsBpiCmtsKeyReplies Counter32,
docsBpiCmtsKeyRejects Counter32,
docsBpiCmtsTEKInvalids Counter32,
docsBpiCmtsKeyRejectErrorCode INTEGER,
docsBpiCmtsKeyRejectErrorString DisplayString,
docsBpiCmtsTEKInvalidErrorCode INTEGER,
docsBpiCmtsTEKInvalidErrorString DisplayString
}
docsBpiCmtsTEKLifetime OBJECT-TYPE
SYNTAX Integer32 (1..604800)
UNITS "seconds"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"The value of this object is the lifetime, in seconds, the CMTS assigns
to keys for this TEK association."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5
and Appendix A.2."
::= { docsBpiCmtsTEKEntry 1 }
Woundy Informational [Page 29]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmtsTEKGraceTime OBJECT-TYPE
SYNTAX Integer32 (1..1800)
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the grace time for the TEK in seconds.
The CM is expected to start trying to get a new TEK beginning
TEKGraceTime seconds before the TEK actually expires."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Appendix A.1.1.1.6."
::= { docsBpiCmtsTEKEntry 2 }
docsBpiCmtsTEKExpiresOld OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for expiration
of the immediate predecessor of the most recent TEK for this FSM.
If this FSM has only one TEK, then the value is the time of activation
of this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5
and 4.2.2.9."
::= { docsBpiCmtsTEKEntry 3 }
docsBpiCmtsTEKExpiresNew OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the actual clock time for expiration
of the most recent TEK for this FSM."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.5
and 4.2.2.9."
::= { docsBpiCmtsTEKEntry 4 }
docsBpiCmtsTEKReset OBJECT-TYPE
SYNTAX TruthValue
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"Setting this object to TRUE causes the CMTS to invalidate the current
active TEK(s) (plural due to key transition periods), and to generate
a new TEK for the associated SID; the CMTS MAY also generate an
unsolicited TEK Invalid message, to optimize the TEK synchronization
Woundy Informational [Page 30]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
between the CMTS and the CM. Reading this object always returns
FALSE."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.1.3.3.5."
::= { docsBpiCmtsTEKEntry 5 }
docsBpiCmtsKeyRequests OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
received a Key Request message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.4."
::= { docsBpiCmtsTEKEntry 6 }
docsBpiCmtsKeyReplies OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted a Key Reply message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.5."
::= { docsBpiCmtsTEKEntry 7 }
docsBpiCmtsKeyRejects OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted a Key Reject message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.6."
::= { docsBpiCmtsTEKEntry 8 }
docsBpiCmtsTEKInvalids OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the count of times the CMTS has
transmitted a TEK Invalid message."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Section 4.2.1.8."
Woundy Informational [Page 31]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
::= { docsBpiCmtsTEKEntry 9 }
docsBpiCmtsKeyRejectErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
unauthorizedSid(4)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in the most recent Key Reject message sent in response to
a Key Request for this BPI SID. This has value unknown(2) if the last
Error-Code value was 0, and none(1) if no Key Reject message has been
received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.6
and 4.2.2.16."
::= { docsBpiCmtsTEKEntry 10 }
docsBpiCmtsKeyRejectErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in the most recent
Key Reject message sent in response to a Key Request for this BPI
SID. This is a zero length string if no Key Reject message has been
received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.6
and 4.2.2.6."
::= { docsBpiCmtsTEKEntry 11 }
docsBpiCmtsTEKInvalidErrorCode OBJECT-TYPE
SYNTAX INTEGER {
none(1),
unknown(2),
invalidKeySequence(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the enumerated description of the
Error-Code in the most recent TEK Invalid message sent in association
with this BPI SID. This has value unknown(2) if the last Error-Code
value was 0, and none(1) if no TEK Invalid message has been received
Woundy Informational [Page 32]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.8
and 4.2.2.16."
::= { docsBpiCmtsTEKEntry 12 }
docsBpiCmtsTEKInvalidErrorString OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..128))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The value of this object is the Display-String in the most recent TEK
Invalid message sent in association with this BPI SID. This is a zero
length string if no TEK Invalid message has been received since reboot."
REFERENCE
"DOCSIS Baseline Privacy Interface Specification, Sections 4.2.1.8
and 4.2.2.6."
::= { docsBpiCmtsTEKEntry 13 }
--
-- The CMTS Multicast Control Group
--
docsBpiMulticastControl OBJECT IDENTIFIER ::= { docsBpiCmtsObjects 4 }
--
-- The CMTS IP Multicast Mapping Table, indexed by IP multicast
-- address and prefix, and by ifindex
--
docsBpiIpMulticastMapTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiIpMulticastMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the mapping of IP multicast address prefixes to
multicast SIDs on each CMTS MAC interface."
::= { docsBpiMulticastControl 1 }
docsBpiIpMulticastMapEntry OBJECT-TYPE
SYNTAX DocsBpiIpMulticastMapEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing the mapping of one IP
multicast address prefix to one multicast SID on one CMTS MAC
interface. The CMTS uses the mapping when forwarding downstream IP
multicast traffic."
Woundy Informational [Page 33]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
INDEX { ifIndex, docsBpiIpMulticastAddress,
docsBpiIpMulticastPrefixLength }
::= { docsBpiIpMulticastMapTable 1 }
DocsBpiIpMulticastMapEntry ::= SEQUENCE {
docsBpiIpMulticastAddress IpAddress,
docsBpiIpMulticastPrefixLength Integer32,
docsBpiIpMulticastServiceId Integer32,
docsBpiIpMulticastMapControl RowStatus
}
docsBpiIpMulticastAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the IP multicast address (prefix) to be
mapped by this row, in conjunction with
docsBpiIpMulticastPrefixLength."
::= { docsBpiIpMulticastMapEntry 1 }
docsBpiIpMulticastPrefixLength OBJECT-TYPE
SYNTAX Integer32 (0..32)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the IP multicast address prefix length
for this row. The value of this object represents the length in
bits of docsBpiIpMulticastAddress for multicast address
comparisons, using big-endian ordering. An IP multicast address
matches this row if the (docsBpiIpMulticastPrefixLength) most
significant bits of the IP multicast address and of the
(docsBpiIpMulticastAddress) are identical.
This object is similar in usage to an IP address mask. The value
0 corresponds to IP address mask 0.0.0.0, the value 1 corresponds
to IP address mask 128.0.0.0, the value 8 corresponds to IP
address mask 255.0.0.0, and the value 32 corresponds to IP
address mask 255.255.255.255."
::= { docsBpiIpMulticastMapEntry 2 }
docsBpiIpMulticastServiceId OBJECT-TYPE
SYNTAX Integer32 (8192..16368)
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object represents the multicast SID to be used in this
IP multicast address prefix mapping entry."
-- DEFVAL is an unused multicast SID value chosen by CMTS.
Woundy Informational [Page 34]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
::= { docsBpiIpMulticastMapEntry 3 }
docsBpiIpMulticastMapControl OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls and reflects the IP multicast address prefix
mapping entry. There is no restriction on the ability to change values
in this row while the row is active."
::= { docsBpiIpMulticastMapEntry 4 }
--
-- The CMTS Multicast SID Authorization Table, indexed by ifIndex by
-- multicast SID by CM MAC address
--
docsBpiMulticastAuthTable OBJECT-TYPE
SYNTAX SEQUENCE OF DocsBpiMulticastAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table describes the multicast SID authorization for each
CM on each CMTS MAC interface."
::= { docsBpiMulticastControl 2 }
docsBpiMulticastAuthEntry OBJECT-TYPE
SYNTAX DocsBpiMulticastAuthEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry contains objects describing the key authorization of one
cable modem for one multicast SID for one CMTS MAC interface."
INDEX { ifIndex, docsBpiMulticastServiceId,
docsBpiMulticastCmMacAddress }
::= { docsBpiMulticastAuthTable 1 }
DocsBpiMulticastAuthEntry ::= SEQUENCE {
docsBpiMulticastServiceId Integer32,
docsBpiMulticastCmMacAddress MacAddress,
docsBpiMulticastAuthControl RowStatus
}
docsBpiMulticastServiceId OBJECT-TYPE
SYNTAX Integer32 (8192..16368)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
Woundy Informational [Page 35]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
"This object represents the multicast SID for authorization."
::= { docsBpiMulticastAuthEntry 1 }
docsBpiMulticastCmMacAddress OBJECT-TYPE
SYNTAX MacAddress
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object represents the MAC address of the CM to which the
multicast SID authorization applies."
::= { docsBpiMulticastAuthEntry 2 }
docsBpiMulticastAuthControl OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls and reflects the CM authorization for each
multicast SID. There is no restriction on the ability to change
values in this row while the row is active."
::= { docsBpiMulticastAuthEntry 3 }
--
-- The BPI MIB Conformance Statements (with a placeholder for
-- notifications)
--
docsBpiNotification OBJECT IDENTIFIER ::= { docsBpiMIB 2 }
docsBpiConformance OBJECT IDENTIFIER ::= { docsBpiMIB 3 }
docsBpiCompliances OBJECT IDENTIFIER ::= { docsBpiConformance 1 }
docsBpiGroups OBJECT IDENTIFIER ::= { docsBpiConformance 2 }
docsBpiBasicCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"This is the compliance statement for devices which implement the
DOCSIS Baseline Privacy Interface."
MODULE -- docsBpiMIB
-- conditionally mandatory group
GROUP docsBpiCmGroup
DESCRIPTION
"This group is implemented only in CMs, not in CMTSs."
-- conditionally mandatory group
GROUP docsBpiCmtsGroup
DESCRIPTION
Woundy Informational [Page 36]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
"This group is implemented only in CMTSs, not in CMs."
-- relaxation on mandatory range (unnecessary since object is read-only)
-- OBJECT docsBpiCmAuthGraceTime
-- SYNTAX Integer32 (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range (unnecessary since object is read-only)
-- OBJECT docsBpiCmTEKGraceTime
-- SYNTAX Integer32 (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range
OBJECT docsBpiCmtsDefaultAuthLifetime
SYNTAX Integer32 (86400..6048000)
DESCRIPTION
"The refined range corresponds to the minimum and maximum values in
operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range
OBJECT docsBpiCmtsDefaultTEKLifetime
SYNTAX Integer32 (1800..604800)
DESCRIPTION
"The refined range corresponds to the minimum and maximum values in
operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range (object removed from MIB)
-- OBJECT docsBpiCmtsDefaultAuthGraceTime
-- SYNTAX INTEGER (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range (object removed from MIB)
-- OBJECT docsBpiCmtsDefaultTEKGraceTime
-- SYNTAX INTEGER (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range
OBJECT docsBpiCmtsAuthCmLifetime
SYNTAX Integer32 (86400..6048000)
DESCRIPTION
Woundy Informational [Page 37]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
"The refined range corresponds to the minimum and maximum values in
operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range (unnecessary since object is read-only)
-- OBJECT docsBpiCmtsAuthCmGraceTime
-- SYNTAX Integer32 (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range
OBJECT docsBpiCmtsTEKLifetime
SYNTAX Integer32 (1800..604800)
DESCRIPTION
"The refined range corresponds to the minimum and maximum values in
operational networks, according to Appendix A.2 in [18]."
-- relaxation on mandatory range (unnecessary since object is read-only)
-- OBJECT docsBpiCmtsTEKGraceTime
-- SYNTAX Integer32 (300..1800)
-- DESCRIPTION
-- "The refined range corresponds to the minimum and maximum values in
-- operational networks, according to Appendix A.2 in [18]."
::= { docsBpiCompliances 1 }
docsBpiCmGroup OBJECT-GROUP
OBJECTS {
docsBpiCmPrivacyEnable,
docsBpiCmPublicKey,
docsBpiCmAuthState,
docsBpiCmAuthKeySequenceNumber,
docsBpiCmAuthExpires,
docsBpiCmAuthReset,
docsBpiCmAuthGraceTime,
docsBpiCmTEKGraceTime,
docsBpiCmAuthWaitTimeout,
docsBpiCmReauthWaitTimeout,
docsBpiCmOpWaitTimeout,
docsBpiCmRekeyWaitTimeout,
docsBpiCmAuthRejectWaitTimeout,
docsBpiCmAuthRequests,
docsBpiCmAuthReplies,
docsBpiCmAuthRejects,
docsBpiCmAuthInvalids,
docsBpiCmAuthRejectErrorCode,
docsBpiCmAuthRejectErrorString,
docsBpiCmAuthInvalidErrorCode,
Woundy Informational [Page 38]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmAuthInvalidErrorString,
docsBpiCmTEKPrivacyEnable,
docsBpiCmTEKState,
docsBpiCmTEKExpiresOld,
docsBpiCmTEKExpiresNew,
docsBpiCmTEKKeyRequests,
docsBpiCmTEKKeyReplies,
docsBpiCmTEKKeyRejects,
docsBpiCmTEKInvalids,
docsBpiCmTEKAuthPends,
docsBpiCmTEKKeyRejectErrorCode,
docsBpiCmTEKKeyRejectErrorString,
docsBpiCmTEKInvalidErrorCode,
docsBpiCmTEKInvalidErrorString
}
STATUS current
DESCRIPTION
"This collection of objects provides CM BPI status and control."
::= { docsBpiGroups 1 }
docsBpiCmtsGroup OBJECT-GROUP
OBJECTS {
docsBpiCmtsDefaultAuthLifetime,
docsBpiCmtsDefaultTEKLifetime,
docsBpiCmtsAuthRequests,
docsBpiCmtsAuthReplies,
docsBpiCmtsAuthRejects,
docsBpiCmtsAuthInvalids,
docsBpiCmtsAuthCmPublicKey,
docsBpiCmtsAuthCmKeySequenceNumber,
docsBpiCmtsAuthCmExpires,
docsBpiCmtsAuthCmLifetime,
docsBpiCmtsAuthCmGraceTime,
docsBpiCmtsAuthCmReset,
docsBpiCmtsAuthCmRequests,
docsBpiCmtsAuthCmReplies,
docsBpiCmtsAuthCmRejects,
docsBpiCmtsAuthCmInvalids,
docsBpiCmtsAuthRejectErrorCode,
docsBpiCmtsAuthRejectErrorString,
docsBpiCmtsAuthInvalidErrorCode,
docsBpiCmtsAuthInvalidErrorString,
docsBpiCmtsTEKLifetime,
docsBpiCmtsTEKGraceTime,
docsBpiCmtsTEKExpiresOld,
docsBpiCmtsTEKExpiresNew,
docsBpiCmtsTEKReset,
docsBpiCmtsKeyRequests,
Woundy Informational [Page 39]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
docsBpiCmtsKeyReplies,
docsBpiCmtsKeyRejects,
docsBpiCmtsTEKInvalids,
docsBpiCmtsKeyRejectErrorCode,
docsBpiCmtsKeyRejectErrorString,
docsBpiCmtsTEKInvalidErrorCode,
docsBpiCmtsTEKInvalidErrorString,
docsBpiIpMulticastServiceId,
docsBpiIpMulticastMapControl,
docsBpiMulticastAuthControl
}
STATUS current
DESCRIPTION
"This collection of objects provides CMTS BPI status and control."
::= { docsBpiGroups 2 }
docsBpiObsoleteObjectsGroup OBJECT-GROUP
OBJECTS {
docsBpiCmtsDefaultAuthGraceTime,
docsBpiCmtsDefaultTEKGraceTime
}
STATUS obsolete
DESCRIPTION
"This is a collection of obsolete BPI objects."
::= { docsBpiGroups 3 }
END
5. Acknowledgments
This document was produced by the IPCDN Working Group. Much of the
content of this MIB was conceived by Chet Birger and Mike StJohns.
Kazuyoshi Ozawa and Bob Himlin provided many useful technical
corrections.
6. References
[1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M. and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC
1155, May 1990.
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,
RFC 1212, March 1991.
Woundy Informational [Page 40]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
[4] Rose, M., "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[5] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Structure of
e Management Information for Version 2 (SMIv2)", STD 58, RFC
2578, April 1999.
[6] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Textual
Conventions for SMIv2", STD 58, RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D. and J. Schoenwaelder, "Conformance
Statements for SMIv2", STD 58, RFC 2580, April 1999.
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Transport
Mappings for Version 2 of the Simple Network Management Protocol
(SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn R. and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol
(SNMPv3)", RFC 2574, April 1999.
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P. and B. Stewart, "SNMP Applications", RFC
2573, April 1999.
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[16] St. Johns, M., editor, "Radio Frequency (RF) Interface
Management Information Base for MCNS/DOCSIS compliant RF
interfaces", RFC 2670, August 1999.
Woundy Informational [Page 41]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
[17] St. Johns, M., editor, "DOCSIS Cable Device MIB, Cable Device
Management Information Base for DOCSIS compliant Cable Modems
and Cable Modem Termination Systems", RFC 2669, August 1999.
[18] "Data-Over-Cable Service Interface Specifications: Baseline
Privacy Interface Specification SP-BPI-I02-990319", DOCSIS,
March 1999, http://www.cablemodem.com/.
[19] "Data-Over-Cable Service Interface Specifications: Cable Modem
Radio Frequency Interface Specification SP-RFI-I05-991105",
DOCSIS, November 1999, http://www.cablemodem.com/.
[20] "Data-Over-Cable Service Interface Specifications: Operations
Support System Interface Specification RF Interface SP-OSSI-RF-
I02-990113", DOCSIS, January 1999, http://www.cablemodem.com/.
[21] "Data-Over-Cable Service Interface Specifications: Baseline
Privacy Plus Interface Specification SP-BPI+-I05-000714",
DOCSIS, July 2000, http://www.cablemodem.com/.
[22] RSA Laboratories, "The Public-Key Cryptography Standards", RSA
Data Security Inc., Redwood City, CA.
[23] Bradner, S., "Key words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[24] Case, J., Mundy, R., Partain, D., and B. Stewart, "Introduction
to Version 3 of the Internet-standard Network Management
Framework", RFC 2570, April 1999.
7. Security Considerations
The Baseline Privacy Interface provides data encryption for DOCSIS
data-over-cable services. Baseline Privacy-capable cable modems have
RSA private/public key pairs installed by manufacturers. The public
key is used to encrypt an Authorization key, and the Authorization
key is used to encrypt one or more Traffic Encryption Keys (TEKs).
The TEKs are used to encrypt both upstream and downstream data
traffic. Please refer to [18] to obtain further information on the
Baseline Privacy specification.
In particular, the Baseline Privacy Interface does not provide an
authentication service. CMTS implementors are encouraged not to rely
on the MAC address of the CM for service authorization -- in
particular, for the docsBpiMulticastAuthTable in this MIB. The
Baseline Privacy Plus Interface does provide a CM authentication
service, and the working group expects to issue a MIB for the
management of BPI+ at a later time.
Woundy Informational [Page 42]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
This MIB specification contains a number of read-write objects, that
should be protected from unauthorized modification to prevent denial
of service and theft of service attacks: in particular, objects that
reset state machines (ex. docsBpiCmAuthReset), change key lifetimes
(ex. docsBpiCmtsDefaultAuthLifetime), change rekeying grace times
(ex. docsBpiCmtsDefaultAuthGraceTime), and control multicast traffic
(ex. most objects in the docsBpiMulticastControl group).
The desired means to protect these objects from unwarranted access is
to implement the security features as provided by the SNMPv3
framework. Specifically, the use of the User-based Security Model
[12] and the View-based Access Control Model [15] is recommended.
Weaker methods to protect CMs from unauthorized access include using
the docsDevNmAccessTable from the Cable Device MIB [17] to disallow
configuration changes from unauthorized network management stations,
and using the SNMP MIB Object and SNMP Write-Access Control
configuration file options from the Radio Frequency Interface [19] to
set MIB object values and disable SNMP SET operations at cable modem
boot time. Note that these mechanisms may be vulnerable to an
unauthorized network management station "spoofing" the source address
of a legitimate network management station.
8. Intellectual Property
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Woundy Informational [Page 43]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
9. Author's Address
Richard Woundy
Cisco Systems
250 Apollo Drive
Chelmsford, MA 01824
U.S.A.
Phone: +1 978 244 8000
EMail: rwoundy@cisco.com
Woundy Informational [Page 44]
RFC 3083 DOCSIS Baseline Privacy MIB March 2001
10. Full Copyright Statement
Copyright (C) The Internet Society (2001). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Woundy Informational [Page 45]
Html markup produced by rfcmarkup 1.129b, available from
https://tools.ietf.org/tools/rfcmarkup/
